Introduction

In the past, coils, step switches, motors, resistors, and other linear loads were used for power distribution and to protect the equipment from surges. However, when non-linear or solid state devices were introduced, the requirement for some new classes of technology for these purposes arose. Then the two devices, surge arresters and surge protectors, were developed. These devices are used to protect conductor wires, transformers, and other equipment from lightning surges. They are responsible to maintain the surge voltages below the basic insulation level of the equipment.

Surge protectors and surge arresters are used for the same work, i.e., protecting equipment from surges. However, many people are confused about their applications. This problem occurs specially in industrial facilities, water treatment plants, and some other important areas. This article explains the difference between these technologies with respect to performance and applications.

Surge arresters

This power distribution device can be used for low, medium, and high voltage applications. Economically, surge arresters are better than surgeSurge Arresters
protectors. Different surge arresters are available based on their withstanding capability. The main problem with them is that they are designed for protecting large electrical distribution systems from lightning surges, and not for sensitive solid state equipment. The surge arresters have high let through voltage, and the value of this voltage exceeds 1200V. It reduces the length of transmission lines by removing shield wires.

Applications

The surge arrester is best to protect insulation of transformers, panel boards, and wirings. However, it doesn’t work well for solid state components.

Surge Protectors

Use of the surge protection devices is increasing continuously with 20% per year. They are used in service entrance, key downstream panel board, and to make clean supply of power to solid state equipment.

APC 10-outlet rackmount surge protector

Image: Wikipedia Commons – APC 10-outlet Rackmount Surge Protector

Applications

• They are used in water treatment plants, hospitals, schools, and telecommunication facilities.

• UPS stops most surges to protect your computer, but it gets damaged itself. Therefore you can use a high quality surge protector to protect your UPS.

• They are used to avoid utility switching and switching electric motors.

• They are best to connect computer devices to one power source outlet.

• If you are using phone lines with your computer via modem, you can use the surge protector that has phone line input jack. This is because phone lines also develop high surges.

• If you are using coaxial cables, then you should use a cable surge protector.

Technical difference between surge arrestors and surge protestors
• Internal Monitoring Capabilities

It is the ability to identify internal failure quickly, and to activate remote alarm or light for indicating the failure. The surge arresters don’t have this quality whereas surge protectors are able to identify failure and to activate a remote alarm or light quickly.

• EMI/RFI filtering

The surge arresters don’t provide the facility of filtering EMI/RFI. However, the high quality surge protectors can do this job.

• Internal Fusing

Internal fusing is defined as protection of the equipment from overload current. This facility is also unavailable in surge arresters whereas you can protect your equipment from overload by using high quality surge protectors.

• Design

The design of surge arresters are based upon gapped MOV design. On the other hand, surge protectors are design by hybrid MOV.

• Interrupts power

Interrupts power and is also known as crowbar. This feature is available in surge arrestors; however, the surge protectors don’t have it.

• Warranty

Surge arresters have limited warranty whereas surge protectors have a warranty of at least of 5 years.

• Life Expectancy

Surge arresters are “use and throw away” type devices, and have limited life. However, surge protectors have a life of more than 25 years if they are sized appropriately.

Summary
A surge protector performs well for your expensive equipment used in your home or office, including in hospitals and other critical areas. However, when comes the protection of large equipment like transformers that work under high voltage, surge arresters are best. Surge arresters are less expensive compared to surge protectors.

Besides, the use of surge protectors has been increasing rapidly. This is because of its features and higher capability of protecting expensive equipment from surges.

Products – Enterprise Software, is presenting a paper about the Objectives, Results, and Challenges of Integrated Volt/VAR Control. Utilities strive to deliver energy within an acceptable voltage range and at a target power factor. This presentation will provide an overview of a pilot project focused on centralizing volt/VAR control, with the objectives of achieving savings for the utility and for the customer and enabling both peak and 24/7 load reduction through voltage reduction, while also delivering a clearer picture of the system parameters. The speaker will address the elements of the business case, project scope, challenges, and results. Daniel Arden has worked in the Utility industry for 18 years, designing, developing, and delivering Advanced Analysis applications for generation, transmission, and distribution centers. His expertise

includes Energy Management Systems (EMS), Outage Management Systems (OMS), Distribution Management Systems (DMS), Distribution Automation (DA), Demand Response (DR), and Geographic Information Systems (GIS). Daniel has a Master’s degree in Electrical Engineering from the University of Minnesota, with a speciality in Power Systems Engineering. Dan is a Member of IEEE and a participant in Distribution Automation and Distribution Reliability committees and the Volt-VAR Management Task Force.Cooper Power Systems initiates and welcomes various opportunities to interact with our customers. Our industry experts exhibit at trade shows around the world, present at conferences, and lead training courses in our factories and at our customer sites. Use the calendar below to find upcoming opportunities to meet with Cooper Power Systems Cooper Power Systems is participating in the Edison Electric Institute Transmission, Distribution and Metering Conference in Chicago, Illinois, on April 29-May 1, 2013. Dan Arden, Cooper Power Systems Director of Global Products – Enterprise Software, is presenting a paper

about the Objectives, Results, and Challenges of Integrated Volt/VAR Control. Utilities strive to deliver energy within an acceptable voltage range and at a target power factor. This presentation will provide an overview of a pilot project focused on centralizing volt/VAR control, with the objectives of achieving savings for the utility and for the customer and enabling both peak and 24/7 load reduction through voltage reduction, while also delivering a clearer picture of the system parameters. The speaker will address the elements of the business case, project scope, challenges, and results. Daniel Arden has worked in the Utility industry for 18 years, designing, developing, and delivering Advanced Analysis applications for generation, transmission, and distribution centers. His expertise

includes Energy Management Systems (EMS), Outage Management Systems (OMS), Distribution Management Systems (DMS), Distribution Automation (DA), Demand Response (DR), and Geographic Information Systems (GIS). Daniel has a Master’s degree in Electrical Engineering from the University of Minnesota, with a speciality in Power Systems Engineering. Dan is a Member of IEEE and a participant in Distribution Automation and Distribution Reliability committees and the Volt-VAR Management Task Force.Cooper Power Systems initiates and welcomes various opportunities to interact with our customers. Our industry experts exhibit at trade shows around the world, present at conferences, and lead training courses in our factories and at our customer sites.

Use the calendar below to find upcoming opportunities to meet with Cooper Power Systems

Cooper Power Systems is participating in the Edison Electric Institute Transmission, Distribution and Metering Conference in Chicago, Illinois, on April 29-May 1, 2013.

Dan Arden, Cooper Power Systems Director of Global Products – Enterprise Software, is presenting a paper about the Objectives, Results, and Challenges of Integrated Volt/VAR Control.

Utilities strive to deliver energy within an acceptable voltage range and at a target power factor. This presentation will provide an overview of a pilot project focused on centralizing volt/VAR control, with the objectives of achieving savings for the utility and for the customer and enabling both peak and 24/7 load reduction through voltage reduction, while also delivering a clearer picture of the system parameters. The speaker will address the elements of the business case, project scope, challenges, and results.

Daniel Arden has worked in the Utility industry for 18 years, designing, developing, and delivering Advanced Analysis applications for generation, transmission, and distribution centers. His expertise includes Energy Management Systems (EMS), Outage Management Systems (OMS), Distribution Management Systems (DMS), Distribution Automation (DA), Demand Response (DR), and Geographic Information Systems (GIS). Daniel has a Master’s degree in Electrical Engineering from the University of Minnesota, with a speciality in Power Systems Engineering. Dan is a Member of IEEE and a participant in Distribution Automation and Distribution Reliability committees and the Volt-VAR Management Task Force.